Nowadays, in order to have a better environment in many places, there are more and more places to install artificial turf. It is not only safe and environmentally friendly, but also can reduce the harm to the body during exercise.
However, there are many things that need special attention in the actual construction and artificial grass installation in London.
The following artificial turf manufacturers in London will tell you in detail.
Design stage
1. Drainage: Is the existing drainage system adequate? Does the artificial grass project area require additional drainage or improved drainage?
2. Soil conditions: Do you need to wet or soften the ground, or remove large rocks with a jackhammer? Rain-soaked soil may need to dry for a few days before the artificial turf project begins
3. Irrigation: Do the remaining trees and plants have sprinklers or bubblers, or does irrigation need to be done first? Identify all irrigation lines, electrical conduits, etc. Underground that may be damaged during the installation of artificial turf.
4. Prevent future damage: Determine if additional supplies are required to prevent damage from rodents or ground animals. Rodent silk (similar to chicken silk) may be suitable. Can a dog pull up artificial grass? If so, the entire perimeter should be protected to prevent the artificial grass from being pulled up or damaged.
5. Existing design elements: Are there specific boundaries? Is it smooth? Do you need to nail into a concrete base? If you are using a curb, edging or edging material, install it before cutting the artificial grass as this will give you a more accurate measurement of the artificial grass installation.
6. Measurement: To reduce labor, carefully measure the project area and design the layout to reduce the number of seams in artificial turf.
7. Design application tip: All synthetic grass products have a grain direction that must be considered. Pay attention to the grain direction and install all fake grass in the same grain pattern. Installing artificial grass in an opposite grain pattern may result in noticeable seams.
Ground preparation
1. Underground Hazards: Irrigation and power lines may be located just below the surface of the project area. Find all irrigation/sprinklers. Cover or remove all unnecessary irrigation/sprinklers. Before you start, turn on the irrigation system and make sure everything is working properly. Do the same for any existing electrical characteristics.
2. Existing Material Removal: Use a turf cutter, shovel and pickaxe to remove all unwanted grass, turf and plants. Remove all unwanted roots, mulch, and large rocks. Rate the bottom layer before artificial grass installation
3. Base preparation: Installing the base surface under the artificial turf in London is crucial to maintaining the stability and integrity of the artificial turf system
4. The substrate should be evenly distributed. Grades and levels meet design and drainage requirements. Shaped to the desired look – flat, lightly rolled, stacked.
5. After the base is installed, the tops of the artificial grass blades must be “higher than any surrounding hardscape
6. If necessary, install anti-rodent wires at this time. Install wires over the entire base area, with a square overlapping. Secure the wires to the ground with lateral staples.
7. If desired, install plywood or treated wood along the perimeter.
Artificial grass device
1. Unfold the synthetic grass and stretch to the prepared bottom. If the artificial turf installation is wrinkled, lay it flat on a flat surface in the sun. Make sure the grain direction of each artificial turf roll is facing the same direction.
2. Use a razor or carpet cutter to cut the artificial turf to fit the project area. All cuts must be made from the back of the artificial turf so that the stitching row is visible. Finish cutting before stitching.
3. When cutting curved edges, cut in small increments to match the design. It is recommended to use a silver marker to draw lines on the back of the artificial turf.
4. If needing to stitch two synthetic turf rolls, trim the edges of each piece so they are very straight. Once the edges of each roll are straight, place them next to each other in the desired position on the base. Make sure the stitches match.
5. Bring the ends of the artificial turf edge together, line up the stitches, fold back the edge of the artificial turf section, and place 6 inches of material under the artificial turf section. Apply weather resistant adhesive material. Fold the two sections of artificial grass together over the seam material to create a seamless piece of artificial grass.
6. Secure the artificial grass around the seam with 6″ or 7″ landscape tacks. Place weights on the seams to hold the artificial grass in place while the glue dries.
7. Attach the artificial grass to the frame:
If there is treated wood around the edges, nail the grass to the treated wood with 20D or 40D nails every 3″ to 6″. If using glue boards around the border, use an air gun to attach synthetic grass.
8. If perimeter material is not used, use 6″ or 7″ stakes to secure the artificial grass around the edges. Space the piles about 12 inches apart along the perimeter edge. Turn on the irrigation system and check that all required sprinklers are covered and pipes are not punctured. Check all electrical lighting. All repair work must be done before infilling the artificial turf.
Artificial grass filler
1. Correct infill installation is critical to maintaining your artificial turf system. The materials used to infill the artificial grass (options include: washed sand and low temperature rubber or acrylic coated sand, washed sand).
The filler material must be evenly distributed. Use a spreader (usually used to spread grass seed, fertilizer, lime, etc.). ) is recommended. Don’t “dump” a lot of filler on fake grass, as it will be difficult to distribute it evenly.
2. Do not attempt to install the infill when the synthetic grass or infill is wet, as the infill will clump.
3. Put the filling material into the spreader and set the dispenser gauge to 5 or medium. Spread the filler material evenly over the artificial grass. Make sure to install the sand products first. Spread 100 pounds of filler material per pass.
4. Between laying layers of fill material, brush synthetic grass fibers upright with a stiff-bristle industrial broom, carpet rake, or electric broom.
5. Repeat the filling process until the filling material is evenly distributed so that no more than “synthetic grass fibers” or leaves are exposed on top of the grass.
6. After the filling process is complete, use a hose to evenly water the entire area to allow the material to settle. The filling can then be adjusted again after drying.
Five, clean up:
Remove all fill material from surrounding hardscape and clear planting areas and pools. Wash or sweep rips and substrate material from surrounding hardscape, and clear planting areas and swimming pools. Wash or sweep tear and substrate material in transit areas. After all these artificial turf installation steps, you now have a comfortable, beautiful lawn that you can enjoy for many years to come.
For artificial grass installation you can visit prestige lawns near Milton Keynes